PRODUCTS

Home

Electronic Copper Tape

Application：lt is mainly used for electronic parts.

Characteristic：It has excellent thermal conductivity, electrical conductivity and flexibility.

hwywfzb@htgd.com.cn

+86-15084626001

Category：

Electronic

Product Inquiry

File Download

Chemical composition

Designation				Composition (mass fraction) /%
GB	EN	ASTM	JIS	Cu	P	Fe	Pb	Sn	Zn	Mn	Ni+Co
T2	Cu-ETP	C11000	C1100	≥99.90	-	≤0.005	≤0.005	-	-	-	-
H95	CuZn5	C21000	C2100	94.0-96.0	-	≤0.05	≤0.05	-	Rem.	-	-
H90	CuZn10	C22000	C2200	89.0-91.0	-	≤0.05	≤0.05	-	Rem.	-	-
H85	CuZn15	C23000	C2300	84.0-86.0	-	≤0.05	≤0.05	-	Rem.	-	-
H80	CuZn20	C24000	C2400	78.5-81.5	-	≤0.05	≤0.05	-	Rem.	-	-
H70	CuZn30	C26000	C2600	68.5-71.5	-	≤0.10	≤0.10	-	Rem.	-	-
H68	CuZn32	C26200	-	67.0-70.0	-	≤0.10	≤0.10	-	Rem.	-	-
H65	CuZn35	C27000	C2680	63.0-68.5	-	≤0.07	≤0.07	-	Rem.	-	-
H62	CuZn38	C27400	-	60.0-63.5	-	≤0.15	≤0.15	-	Rem.	-	-
QSn6-0.2	CuSn6	C51900	C5191	Rem.	0.03-0.35	≤0.10	≤0.10	5.0-7.0	≤0.30	-	-
QSn8-0.3	CuSn8	C52100	C5210	Rem.	0.03-0.35	≤0.10	≤0.10	7.0-9.0	≤0.20	-	-
BZn18-18	CuNi18Zn18	C75200	C7521	63.0-66.5	-	≤0.25	≤0.25	-	Rem.	≤0.50	16.5-19.5
BZn18-26	CuNi18Zn26	C77000	C7701	53.5-56.5	-	≤0.25	≤0.25	-	Rem.	≤0.50	16.5-19.5

Properties

Designation				Condition	Thickness/mm	Rm/MPa Tensile strength	A50/% Elongation	Vickers hardness/HV
GB	EN	ASTM	JIS	Condition	Thickness/mm	Rm/MPa Tensile strength	A50/% Elongation	Vickers hardness/HV
T2	Cu-ETP	C11000	C1100	O60	0.10-8.00	≥195	≥25	≤70
				H01	0.10-8.00	215-295	≥23	60-95
				H02	0.10-8.00	245-345	≥8	80-110
				H04	0.10-8.00	295-395	≥3	90-120
				H06	0.10-8.00	≥350	-	≥110
H95	CuZn5	C21000	C2100	O60	≥0.2	≥215	≥30	-
H95	CuZn5	C21000	C2100	H04	≥0.2	≥320	≥3	-
H90	CuZn10	C22000	C2200	O60	≥0.2	≥245	≥35	-
				H02	≥0.2	330-440	≥5	-
				H04	≥0.2	≥390	≥3	-
H85	CuZn15	C23000	C2300	O60	≥0.2	≥260	≥40	≤85
				H02	≥0.2	305-380	≥15	80-115
				H04	≥0.2	≥350	-	≥105
H80	CuZn20	C24000	C2400	O60	≥0.2	≥265	≥50	-
H80	CuZn20	C24000	C2400	H04	≥0.2	≥390	≥3	-
H70 H68 H65	CuZn30 CuZn32 CuZn35	C26000 C26200 C27000	C2600 - C2680	O60	≥0.2	≥290	≥40	≤90
				H01	≥0.2	325-410	≥35	85-115
				H02	≥0.2	355-460	≥25	100-130
				H04	≥0.2	410-540	≥13	120-160
				H06	≥0.2	520-620	≥4	150-190
				H08	≥0.2	≥570	-	≥180
H62	CuZn38	C27400	-	O60	≥0.2	≥290	≥35	≤95
				H02	≥0.2	350-470	≥20	90-130
				H04	≥0.2	410-630	≥10	125-165
				H06	≥0.2	≥585	≥2.5	≥155
QSn6-0.2	CuSn6	C51900	C5191	O60	≥0.15	≥315	≥40	≤120
				H01	≥0.15	390-510	≥35	110-155
				H02	≥0.15	490-610	≥10	150-190
				H04	≥0.15	590-690	≥8	180-230
				H06	≥0.15	635-720	≥5	200-240
				H08	≥0.15	≥690	-	≥210
QSn8-0.3	CuSn8	C5210	C5210	O60	>0.15	≥340	≥45	≤120
				H01	>0.15	390-510	≥40	100-160
				H02	>0.15	490-610	≥30	150-205
				H04	>0.15	590-705	≥12	180-235
				H06	>0.15	685-785	≥5	210-250
BZn18-26	CuNi18Zn27	C77000	C7701	H01	≥0.2	≥475	≥25	≤165
				H02	≥0.2	540-650	≥11	140-195
				H04	≥0.2	≥645	≥4	≥190
BZn18-18	CuNi18Zn18	C75200	C7521	O60	>0.15	≥385	≥35	≤105
				H01	>0.15	400-500	≥20	100-145
				H02	>0.15	460-580	≥11	130-180
				H04	>0.15	≥545	≥3	≥165

NOTE: Other products with performance requirements can also be supplied after negotiation between the supply and demand parties.

Thickness and tolerances（Copper and brass）

Designation

Thickness/mm

Width/mm

≤200

>200-300

>300-400

>400-600

Thickness on tolerances/mm

ASTM

JIS

Common level

Higher level

Common level

Higher level

Common level

Higher level

Common level

Higher level

H95

H90

H85

H80

H70

H68

H65

Cu-ETP

CuZn5

CuZn10

CuZn15

CuZn20

CuZn30

CuZn32

CuZn35

C11000

C21000

C22000

C23000

C24000

C26000

C26200

C27000

C1100

C2100

C2200

C2300

C2400

C2600

C2680

>0.15-0.25

±0.015

±0.005

±0.01

±0.005

±0.01

±0.005

±0.01

±0.005

>0.25-0.35

±0.020

±0.005

±0.01

±0.005

±0.01

±0.005

±0.01

±0.007

>0.35-0.50

±0.025

±0.007

±0.01

±0.007

±0.01

±0.007

±0.015

±0.01

>0.50-0.80

±0.030

±0.01

±0.007

±0.015

±0.01

±0.015

±0.01

>0.80-1.20

±0.040

±0.015

±0.001

±0.02

±0.015

±0.02

±0.015

>1.20-2.00

±0.050

±0.02

±0.015

±0.025

±0.02

±0.025

±0.02

>2.00-3.00

±0.060

±0.025

±0.02

±0.025

±0.03

±0.025

±0.03

±0.025

NOTE: If the dimensional tolerance required by the demander is single positive or single negative tolerance, the value shall be twice the corresponding value in the table.

Thickness and tolerances（Bronze and white copper）

Designation				Thickness/mm	Width/mm
					≤400		>400-600
					Thickness on tolerances/mm
GB	EN	ASTM	JIS		Common level	Higher level	Common level	Higher level
QSn6-0.2 QSn8-0.3 BZn18-26 BZn18-18	CuSn6 CuSn8 CuNi18Zn27 CuNi18Zn18	C51900 C52100 C77000 C75200	C5191 C5210 C7701 C7521	>0.15-0.25	±0.01	±0.005	±0.030	±0.020
				>0.25-0.40	±0.01	±0.005	±0.040	±0.030
				>0.40-0.55	±0.01	±0.007	±0.050	±0.045
				>0.55-0.70	±0.015	±0.01	±0.060	±0.050
				>0.70-0.90	±0.025	±0.015	±0.070	±0.060
				>0.90-1.20	±0.02	±0.015	±0.080	±0.070
				>1.20-1.50	±0.25	±0.02	±0.090	±0.080
				>1.50-2.00	±0.080	±0.050	±0.100	±0.090
				>2.00-2.60	±0.03	±0.025	±0.120	±0.100

NOTE: If the dimensional tolerance required by the demander is single positive or single negative tolerance, the value shall be twice the corresponding value in the table.

Width and tolerances

Thickness/mm	Width/mm
	≤200	>200-300	>300-600
	Width on tolerances/mm
>0.15-0.50	±0.1	±0.2	±0.2
>0.50-2.00	±0.1	±0.2	±0.2
>2.00-3.05	±0.1	±0.2	±0.2

NOTE: If the dimensional tolerance required by the demander is single positive or single negative tolerance, the value shall be twice the corresponding value in the table.